Strenx 700 mc meet or exceed the requirements of s700mc in en 101492. Its highstrength combined with naturally stiff form enables construction of stronger and lighter structures. Meets the requirements of en 100256 norm for the s690 degree. Hardox 450 the most popular structural wear plate ssab.
S700mc can be supplied as steel plate sheet, round steel bar, steel tubepipe, steel stripe, steel billet, steel ingot, steel wire rods. Weldox 0 is available in widths up to 2900 mm and lengths up to 14630 mm. Strenx tm has been developed for highstrength and highperformance structural steels, it also provides the widest ranges of strengths and dimensions for structural steel which. Strenx mc steels have a guaranteed minimum bending radius, valid for both longitudinal and transversal directions, that are closer than standard en 10 149. Typical applications are load carrying structures having very high demands on low weight. Weldox 700 meets the requirements of en 10025 for the corresponding grades. Strenx the highstrength, high performance steel there will always be a battle for the higherperforming steel product, but thin and strong will always come first. Strenx 700 mc meets or exceeds the requirements of s700mc in en 101492. Strenx 960 meets the requirements of en 10 0256 for the s960 ql grade and thicknesses. The product data sheet assigned to a specific product holds all valid and guaranteed properties. Strenx 0 strenx 1100 strenx 960 strenx 900 strenx 700 strenx 650 strenx 600 strenx 100110 strenx tube strenx sections. Strenx tube 700qlh is plasmawelded, quenched and tempered hollow section with a minimum yield strength of 700 mpa. Hardox 500 plate data sheet 152uk hardox 500 plate 20161103 general product description the bendable, weldable and highly abrasionresistant steel. Hardox 450 is an abrasionresistant steel with a nominal hardness of 450 hbw.
The 700 series has a yield strength of 700 mpa, whereas with strenx 900 the value is 900 mpa. Hardox 450 steel is intended for applications where demands are imposed on abrasion resistance with good cold bending applications. Data sheet 2004 strenx 600 mc 20150408 general product description the highstrength structural steel at 600 mpa strenx 600 mc is a hotrolled structural steel made for cold forming, with a minimum yield strength of 600 mpa for stronger and lighter structures. Available dimensions strenx 700 mc plus is available as cut to length sheets in thicknesses of 3. Strenx 700 is a general structural steel with a minimum yield strength of 650 700 mpa depending on thickness. A premium and trademarked brand of formable abrasion resistant plates produced by ssab with a nominal brinell hardness of 450. Strenx 960 the highstrength structural steel at 960 mpa strenx 960 is a structural steel that guarantees a minimum yield strength of up to 960 mpa depending on thickness.
Data sheet strenx 100 00010101 general product description the highstrength, highperformance steel strenx 100 is a structural steel with a minimum yield strength of 100 ksi. Data sheet 2006 strenx 700 20160412 general product description the highstrength structural steel at 650 700 mpa strenx 700 is a structural steel with a minimum yield strength of 650 700 mpa depending on thickness. Fatigue life of high strength steel for cold forming article pdf available in metalurgija sisak then zagreb 5612. Strenx 100 xf is a cold forming steel for light and heavy transport solutions and components. Strenx 700 e complies with s690ql is available in plate thicknesses of 4 160 mm, while. Strenx 700 260 300 320 430 500 350 400 450 500 550 600 675 24 29 32 43 49 35 40 44 49 52 55 62 860 935 990 40 1580 1080 1250 1400 1580 1760 1940 strenx 900 strenx 960 strenx 1100 strenx 0 hardox hituf hardox 400 hardox 450 hardox 500 hardox 550 hardox 600 hardox extreme strenx performance steel and. Available dimensions strenx 100 xf is available in thicknesses of 0. Allow psx 700 to dry to touch before exposing to curing temperatures above 60c140. Strenx 650 mc advanced high strength steel general product description strenx 650 mc is a hotrolled structural coldforming steel with a minimum yield strength of 650 mpa intended to give stronger and lighter structures.
Data sheet 2007 strenx 700 cr 20170420 strenx 700 cr general product description the highstrength structural steel at 700 mpa strenx 700 cr is a coldrolled structural steel with a minimum yield strength of 700 mpa used to produce stronger and lighter structures. Weldox 0 is a general structural steel with a minimum yield strength of 0 mpa. Available dimensions weldox 700 e is available in plate thicknesses of 4 160 mm and weldox 700. Available dimensions weldox 700 e is available in plate thicknesses of 4 160. Strenx 100 has obtained its mechanical properties by quenching and subsequent tempering. Available dimensions weldox 0 is available in plate thicknesses of 4 10 mm. Strenx 700 e complies with s 690 ql is available in plate thicknesses of 4160 mm, while.
Strenx 960 general product description strenx 960 is a general structural steel that, depending on thickness, guarantees minimum yield strength up to 960 mpa. Here, each number represents the steels yield strength. Strenx 700mc meets or exceeds the requirements of s700mc in en 101492. Typical applications include demanding loadbearing structures. Strenx 700 cr is available as coils and cut to length sheets in thicknesses of 0.
Still, the values depend on the material thickness. The bending guarantees also conform to en iso 7438. Strenx tube 700qlh meets or exceeds the requirements of pren 10210 2016. The highstrength structural steel with excellent formability. Data sheet 2009 strenx 700 mc plus 20170420 strenx 700 mc plus general product description the highstrength structural steel with excellent formability strenx 700 mc plus is a highstrength structural steel with advanced cold formability and impact toughness for highly demanding applications. Strenx 100 general product description strenx 100 is a structural steel with a minimum yield strength of 100 ksi. Strenx 700 mc plus is a hotrolled structural steel with a minimum yield strength of 700 mpa intended to. The highstrength structural steel at 650 700 mpa strenx 700 is a structural steel with a minimum yield strength of 650 700 mpa depending on thickness. The extreme cleanliness, lean alloy solution and highquality manufacturing process of strenx steels have a very positive impact on toughness, fatigue strength and performance in subzero conditions.
Data sheet 2008 strenx 700 mc 20170420 strenx 700 mc general product description the highstrength structural steel at 700 mpa strenx 700 mc is a hotrolled structural steel made for cold forming, with a minimum yield strength of 700 mpa for stronger and lighter struc tures. Contact sales subscribe today to the quarterly special steels newsletter. It is a hotrolled product that is available in high strength and extrahigh strength coldforming steels. Available dimensions strenx 100 is supplied in plate thicknesses of 316 5 inches. Hardox, weldox, armox and toolox are registered trademarks that are owned by ssab technology ab. Strenx 700 meets the requirements of en 10 0256 for the s 690 grade and thicknesses.
The most popular abrasionresistant steel with excellent structural properties. Data sheet 2045 strenx section 700 20150408 strenx section 700 corner radius 2. Data sheet 2040 strenx tube 700mh 20170420 strenx tube 700mh general product description strenx tube 700mh is an hfwelded coldformed structural hollow section made of hotrolled highstrength steel with a minimum yield strength of 700 mpa. General product information weldox, hardox, armox and toolox. Raex 500 data sheet raex 500 00010101 general product description sold only through certifled partners ssab now sells raex the highstrength, wearresistant steel with good hardness and impact toughness exclusively through ssabs certified partner network. Data sheet 2045 strenx section 700 20170420 strenx section 700 general product description strenx section 700 is a coldformed steel section made of hotrolled, highstrength steel with a minimum yield strength of 700 mpa. All classes conform to or are closer than the requirements in en 10 0256. Workshop guidelines for strenx 100 refer to the same recommendations as for strenx 700. Pdf fatigue life of high strength steel for cold forming.
Flush equipment with thinner or cleaner 9058 before use. Data sheet 2005 strenx 650 mc 20150408 general product description the highstrength structural steel at 650 mpa strenx 650 mc is a hotrolled structural steel made for cold forming, with a minimum yield strength of 650 mpa for stronger and lighter structures. Strenx 700 mc meets or exceeds the requirements of s700mc in en. Recommended maximum heat input qmax versus sheet thickness for strenx 900 plus and strenx 960 plus butt weld. Data sheet 2008 strenx 700 mc 20150408 general product description the highstrength structural steel at 700 mpa strenx 700 mc is a hotrolled structural steel made for cold forming, with a minimum yield strength of 700 mpa for stronger and lighter structures. Strenx 650 mc meet or exceed the requirements of s650mc in en 101492. Data sheet 2006 strenx 700 20170420 strenx 700 general product description strenx 700 is a structural steel with a minimum yield strength of 650 700 mpa depending on thickness. Typical applications include a wide range of components and parts in demanding loadbearing structures. Strenx tube 700mlh advanced highstrength structural hollow sections strenx tube 700mlh is an hfwelded coldformed structural hollow section made of hotrolled highstrength steel with a minimum yield strength of 700 mpa. Typical applications can be a wide range of components and parts, for example demanding load bearing structures. Hardox 450 combines good bendability and weldability with an option for guaranteed impact toughness hardox 450 tuf. Strenx 650 mc meets or exceeds the requirements of s650mc in en 101492.
Typical applications are a wide range of components and parts for example loadbearing structures. Strenx 600 mc meets or exceeds the requirements of s600mc in en 101492. Recommended maximum heat input qmax versus sheet thickness for strenx 1100 mc butt weld. The chemical analysis, consisting of low levels of. Strenx 700 mc structural steel with excellent cold. Strenx 700 mc plus meet or exceed the requirements of s700mc in en 101492. Hardox 500 is a bendable and weldable abrasionresistant steel, with a nominal hardness of 500 hbw. Corrosionresistant steels, wearresistant steels, sheet steel for ballistic protection, electrical sheet steel and hardenable steels are all members of the domex family. Strenx 700 is a structural steel with a minimum yield strength of 650700 mpa depending on thickness.
A structural steel developed for use in demanding loadbearing. Tolerances more details are given on thickness tolerances according to strenx thickness guarantees. The strenx 700mc steel for cold shaping is a hotrolled steel formed in a thermal. Strenx guarantees offer considerably narrower thickness tolerances compared to en 10 051. Tolerances more details are given in ssabs brochure 41general product information weldox, hardox, armox and tooloxuk or on thickness tolerances according to ssabs thickness precision guarantee accurolltech. Ssab is the worlds most experienced producer of highend quenched and tempered steels. Weldox 700 meets the requirements of en 10025 for the corresponding grades and thicknesses. Strenx 700 meets the requirements of en 10 0256 for the s690 grade and thicknesses. If needed for workability, thin with recommended thinner up to. Mechanical properties yield strength r p0,2 min mpa tensile strength r m mpa elongation a 80 min % sheet thickness t. Strenx 700 mc structural steel with excellent cold formability ssab. Parts produced from the asrolled green plates are typically heat treated to obtained a combination of high strength and toughness. Strenx 960 meets the requirements of en 10 0256 for the s 960 grade and thicknesses. Suitable for applications that demand higher wear resistance.
Strenx 700 mc advanced high strength steel general product description strenx 700 mc is a hotrolled structural coldforming steel with a minimum yield strength of 700 mpa intended to give stronger and lighter structures. Typical applications include demanding load bearing structures. The application specially for loadbearing and support structures with tough demands, where comes first the resistance with weight reduction. Data sheet 2044 strenx section 650 20150408 general product description advanced highstrength, coldformed steel section strenx section 650 is a coldformed steel section made of hotrolled, highstrength steel with a minimum yield strength of 650 mpa. Ssab introduces strenx 700 ome performance steel which meets abs, dnvgl and lloyds register classification rules. Strenx 100 meets the requirements of astm a514, grade s, for thicknesses up to 2 12 inch. Its high strength, combined with naturally stiff form of the welded hollow section, enables construction of stronger and lighter structures.
Tolerances more details are given in ssabs brochure 41general product information weldox, hardox, armox and tooloxuk or on thickness tolerances according to ssabs thickness precision guarantee accrolltech. Whatever your application, strenx offers new options. Mechanical properties wall thickness mm yield strength r eh 12 min mpa tensile strength r m mpa. Stainless steel, special steel, compressor blading, turbine blading, superalloy supplier. The highstrength structural steel at 650700 mpa strenx 700 is a structural steel with a minimum yield strength of 650700 mpa depending on thickness.
Data sheet 2006 strenx 700 20150408 general product description the highstrength structural steel at 650 700 mpa strenx 700 is a structural steel with a minimum yield strength of 650 700 mpa depending on thickness. Strenx 700mc is a hotrolled structural steel made for cold forming, with a minimum yield strength of 700 mpa for stronger and lighter structures. Weldox 700 is a general structural steel with a minimum yield strength of 650 700 mpa depending on thickness. The astm a829 specification is the standard specification for alloy structural steel plates produced to chemical composition requirements and delivered in the asrolled green condition. Data sheet 2041 strenx tube 700 mlh 20150422 strenx tube 700mlh fabrication and other ecommendationsr welding, bending and machining strenxtube 700 mlh has good weldabilility, including corner region, and it is suitable for thermal cutting. Fabrication and other recommendations welding, bending and machining recommendations are found in ssabs brochures at. Strenx 700 products are structural steel with a minimum yield strength of 650 700 mpa depending on thickness. Strenx 700 cr advanced high strength steel general product description strenx 700 cr is a coldrolled structural steel with a minimum yield strength of 700 mpa intended to give stronger and lighter structures. The dualcertified strenx 700 ome meets the standard requirements of abs ab eq70 dnvgl nve 690 lr eh69. Available dimensions strenx 700 e is available in plate thicknesses of 4 160 mm and. Strenx 700 strenx 900 strenx 960 strenx 1100 strenx 0 53100 53100 53100 5. All the common welding methods are suitable with matching or undermatching consumables. S700mc round bar s700mc flat bar s700mc hollow bar s700mc tube pipe s700mc sheet plate s700mc strip coil s700mc wire s700mc forging s700mc tube pipe tel.
180 853 565 537 850 1102 727 949 960 74 50 1021 987 512 1328 937 1067 1138 278 581 284 450 172 716 269 1469 513